If getting a replacement from Apple is out of your price range and you'd prefer to just fix it yourself, follow along and we'll show you how. Disclaimer: As with any repair, iMore cannot be held responsible for any damage you may do to your device. It's also worth considering that opening up your device to perform any repair or modification can and will void your Apple warranty. IPod Touch Repair. If you don't feel comfortable opening your device, don't. Use extreme care and caution when performing a repair on any device. What you need to replace a 4th gen iPod touch digitizer and LCD iMore recommends using only quality and genuine parts from a reputable supplier like. They have quality parts, tools, and much more for all your repair needs. • 4th generation iPod touch (black or white) • Replacement display • Hair dryer or heat gun • Extra strength double-sided replacement adhesive — there are several types of adhesive kits you can buy or you can cut your own but we recommend using a pre-cut kit as it will make the process much simpler • Standard #000 Phillips screwdriver • Spudger tool • Razor blade • iSesamo Opening tool (not necessary but awesome for prying up cables and getting under adhesive) Power off your iPod touch Before attempting to open your iPod touch or perform and kind of repair, always power it off first. Just hold down the power button until the Slide to power off message appears on the screen. Slide with your finger and wait for the device to completely power down before continuing. Areas to look out for when removing the touch screen and LCD assembly While other devices such as the iPhone and older iPod touches are held together with either screws or clips, the iPod touch and it's larger iPad sibling hold the display in with a strong adhesive. We'll need to soften it by heating it up before we can remove it. There are a few areas you'll need to be careful of when attempting to pry off the iPod touch front assembly. Notice in the picture below where these areas are and use your pry tool and metal spatula with caution when moving around these areas so you don't tear any cables. Once you've taken a mental note of the areas above and where they're located under the screen, proceed to the next step. Remove the broken screen and LCD assembly • First, turn your heat gun on the lowest setting possible and heat up the bottom left edges of the iPod. Be careful when lifting it up or handling it as the edges can get quite hot. This works best if you heat and pry small sections at a time so you can hold the other side in your hand. • Once you've gotten a section heated, use your metal spatula and/or pry tool in order to slowly work up the LCD and digitizer assembly by gently lifting up between the gasket and screen edge. • After you've managed to free a small section, heat up the next section and slowly work your way around until you've broken the adhesive all the way around being extra careful around the areas from the previous section. If the glass spiders or cracks further, that's okay as you'll be replacing the entire front assembly. • Once you've gotten a majority of the adhesive separated you'll be able to lift up the entire front assembly. Use your pry tool to remove the LCD cable with one hand. The digitizer cable that connects underneath the logic board you can clip with a pair of scissors as you'll be replacing it. • Set the old assembly aside but don't throw it away as you'll need a few parts off of it before reassembly. Remove the old ashesive and clean off the frame Before replacing the assembly or disassembling your iPod touch any further, now is a good time to clear out the frame from all the old ashesive and any broken glass pieces that may be stuck on the interior of the frame. If you don't make sure all dust, debris, and glass is removed before placing in the new screen, it will not fit in correctly and you'll have to go back and re-clean it. In other words, make absolutely sure that you are removing all of the debris and glass before continuing. Feel free to use air duster to blow out any excess debris if needed. Remove the camera retainer clip Towards the top of the iPod touch is a retainer clip that holds the rear camera in place. Use your pry tool or metal spatula in order to pop it up and remove it. Set it aside for reassembly. Driver genius 12 0 0 1211 final and crack rar file. Remove the copper tape holding the logic board shield down Underneath the camera retainer clip is a tiny piece of copper tape that's connected to the underside of the logic board shield. Use your metal spatula and your fingers to gently peel the tape back. Do not completely remove it but just pry the part that is covering the rear facing camera off. Remove the logic board shield The logic board shield is also held down with a bit of adhesive that we will have to break but first we need to remove some screws. • Remove the screws outlined in the picture below with your #00 Phillips screwdriver making sure to order them in a way that you'll remember when it comes time for reassembly. • Use your heat gun to heat up the top and the bottom of the logic board shield. This will make it easier to remove the logic board shield. • Start at the bottom by slipping the metal spatula between the shield and speaker assembly. Be careful not to pry the speaker assembly up with the shield as the wires are delicate and can tear easily. Once you have loosened both sides of the bottom of the shield we can move on. • Now move your metal spatula to the position indicated in the picture below taking care to slip it between the cable connected on the logic board. While you can pry up on either side, I find it easier to push up gently to break the adhesive in this position as your tool will hold the cable down and prevent it from breaking off the logic board. Prying directly up on either side can cause this to happen so go slowly on this step and position your tool in a way that will not damage the small cable running underneath. • Once you've broken the adhesive in the top portion, the shield should lift right off of the logic board. ![]() Set it aside for reassembly later. Pry up the rear facing camera We don't need to completely remove the rear facing camera but prying it up will allow us to lift up the logic board a bit more and make attaching the digitizer cable a bit easier. Use your pry tool to gently lift the rear facing camera out of its opening and move on to the next step. Remove the top 3 screws holding the logic board down Even though we won't be removing the logic board, we will need to get underneath it in order to attach the digitizer cable for the new digitizer and LCD assembly. Use your #00 Phillips screwdriver to remove the screw screws labeled below making sure to place them in and order you'll remember for reassembly. Now that you've removed the 3 screws along the top of the logic board we can continue on to prying up part of the logic board. Pry up the top of the logic board You do not want to remove the entire logic board but only pry up the top portion. Be extremely careful with this step as the logic board is fragile and can break easily. • Use your pry tool or metal spatula to lift up the portion of the logic board highlighted in the picture below. The logic board is slightly pliable and will bend easily. This is normal. Only pry up enough to edge your finger along it. • Now run your finger towards the top of the logic board so the part of the logic board that houses the front facing camera and the digitizer cable can be lifted enough for you to pull out the digitizer cable. Peel up the copper tape around the digitizer cable There is a piece of copper tape wrapped around the digitizer cable that you'll need to remove in order to pry off the digitizer cable. Use your pry tool and/or metal spatula to pry up and edge of the tape. Then move along the other side and find the edge of the copper tape and peel it back. Once you've gotten the tape removed from the front of the cable area, you can move on to removing the cable as the tape will come off with it. Remove the remaining digitizer cable end and copper tape While holding the logic board up with one hand, use the pry tool in your other hand to gently push down on the top of the cable until it pops off the bottom of the logic board. Once the cable has popped off the underside of the logic board you can gently slide it out. Peel off the copper tape that remains on the old digitizer cable piece. We will place it on the new one in a later step. Florida trial court public access. Ready the new digitizer and LCD assembly You will only need to perform this step if the replacement LCD and digitizer assembly you have does not have a Home button and camera shield pre-assembled. If it does not, use this step to transfer the Home button and camera shield to the new assembly.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |